 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. Part No. AL-00-2UY1CT High Power Diff No. TypeLED Lamps Package Dimension: Notes: 1. All dimensions are in millimeter. 2. An epoxy meniscus may extend about. 1.5mm(0.059") down to the lead 3. Tolerances unless Dimension 0.25mm. 1 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. Part No. AL-00-2UY1CT High Power Diff No. TypeLED Lamps Lens Color Water Clear LED Parts P/N. AL-00-2UY1CT Chip Material Emitted Color AlGaInP Super Yellow Absolute Maximum Ratings at Ta=25 Parameter Continuous Forward Current Operating Temperature Storage Temperature Soldering Temperature Electrostatic Discharge Power Dissipation Peak Forward Current Duty 1/10@1KHz Reverse Voltage Symbol IF Topr Tstg Tsol ESD PD IFPeak VR Rating 60 -25 to +80 -40 to +100 260 5 1000 180 100 5 Unit mA V mW mA V Electronic Optical Characteristics : Parameter Luminous Intensity Viewing Angle Peak Wavelength Dominant Wavelength Spectrum Radiation Bandwidth Forward Voltage Reverse Current Symbol IV 21/2 p d VF IR Min. 700 585 1.8 Typ. 1000 150 590 590 30 2.0 Max. 595 2.6 10 Unit Condition mcd deg nm nm nm V A IF=60mA IF=60mA IF=60mA IF=60mA IF=60mA IF=60mA VR=5V 2 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. Part No. AL-00-2UY1CT High Power Diff No. TypeLED Lamps Reliability test items and conditions : The reliability of products shall be satisfied with items listed below. Confidence level: 90% LTPD: 10% Test Sample NO ITEM Test Conditions Ac/Re hours/cycle Q'ty 1 Solder Heat Temp2605 H+85 30min 2 Temperature Cycle 5min 100 cycles 80 pcs 0/1 5 sec 80 pcs 0/1 L-40 30min H+100 5min 3 Thermal Shock 10sec 100 cycles 80 pcs 0/1 L-10 5min 4 5 6 7 High Temperature Storage Low Temperature Storage DC Operating Life High Temperature High Humidity Ta=100 Ta=-40 Temp25 IF=20mA 8585%RH 1000 hrs 1000 hrs 1000 hrs 1000 hrs 80 pcs 80 pcs 80 pcs 80 pcs 0/1 0/1 0/1 0/1 3 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. Part No. AL-00-2UY1CT High Power Diff No. TypeLED Lamps 4 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. Part No. AL-00-2UY1CT High Power Diff No. TypeLED Lamps 5 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. Part No. AL-00-2UY1CT High Power Diff No. TypeLED Lamps Precautions For Use 1. Over-current proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 6 |
Price & Availability of AL-00-2UY1CT
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |